How do you actually feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the job can relocate quickly; if you have to open a wall surface to eliminate the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have certified on your own for the job and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to think about using one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This short article will assist you set up a new tub in your shower room if you have actually currently gotten a brand-new bathtub and don't require to change the arrangement of your previous supply of water pipes.
Your tools as well as material list must consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Secure the faucet in place with the manufacturer offered backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The former type needs to be connected to the faucet ends initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Tub
Utilizing the two wood boards under its feet, position the tub in the needed setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub till the spirit level reads degree.
To set up taps, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; after that do the same for the various other tap.
Switch on the water as well as inspect all joints as well as new pipework for leaks as well as tighten them if essential. Load the tub as well as likewise check the overflow outlet and the typical outlet for leaks.
Lastly, fix the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait till the bath tub has been used at least when as this will resolve it right into its last setting.
Preparing for the Setup
To start with, the sustaining frame supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface in between the bath and also the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can fracture fairly very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very drawn to A Step-by-Step Guide to Installing a Bathtub and I am assuming you appreciated our article. So long as you enjoyed reading our blog post if you please don't forget to share it. We recognize the value of reading our article about How to Install a Bathtub.
Get A Free Quote